Plumbing Basics: Your Starting Point for When Installing a Bathtub
Plumbing Basics: Your Starting Point for When Installing a Bathtub
Blog Article
How do you really feel about How to Install a Bathtub?
Mounting a bathtub isn't exactly brain surgery, but it does require strong plumbing, woodworking, as well as sometimes, tiling abilities. Replacing an old tub with a new one is additionally a moderately tough task. If the old bathtub is conveniently available, the project can move quickly; if you have to open up a wall surface to get rid of the old bathtub and also position the brand-new bathtub, the task is a lot harder. In either situation, the job is within a home handyman's abilities, although you will need a helper to move out the old bathtub and set in the brand-new one. Make certain you have actually certified yourself for the task as well as fit attempting it. As opposed to employing a professional to take control of a halfway-completed job, it is far better to take into consideration utilizing one prior to you start. Opportunities are you might require an expert plumber to make tube links.
This post will aid you mount a new bathtub in your restroom if you have actually currently gotten a brand-new bathtub as well as don't require to alter the arrangement of your previous supply of water pipes.
Your tools and also product list should make up the following:
Getting ready for the Installment
Firstly, the supporting frame provided with the bath needs to be fitted (if required) according to the producer's guidelines. Next off, fit the taps or mixer to the bathtub. When fitting the tap block, it is important to ensure that if the tap includes a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is likewise practical to fit a supporting plate under the taps unit to prevent pressure on the bath tub.
Fit the adaptable faucet ports to the bottom of the two faucets making use of 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet with the hole in the bath. Utilize the nut supplied by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. See to it you use all of the supplied washing machines.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath ought to currently be ready to be fitted in its final setting.
Removing Old Taps
If you need to replace old taps with new ones as a part of your installment, after that the first thing you need to do is disconnect the supply of water. After doing so, switch on the faucets to drain pipes any type of water continuing to be in the system. The procedure of getting rid of the existing faucets can be fairly troublesome as a result of the restricted gain access to that is usually the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipes to the faucets. Have a towel ready for the remaining water that will certainly originate from the pipelines. When the supply pipes have actually been removed, use the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from transforming during this procedure. As soon as the taps have been gotten rid of, the holes in the bath/basin will have to be cleaned up of any kind of old securing compound.
Before carrying on to fit the brand-new taps, compare the pipe connections on the old taps to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Mounting the Bathtub
Utilizing both wooden boards under its feet, position the bath tub in the required placement. The wood boards are practical in evenly spreading the weight of the bath tub over the location of the boards instead of focusing all the weight onto 4 small points.
The following objective is to guarantee that the bathtub is leveled all round. This can be accomplished by checking the spirit level and changing the feet on the bathtub up until the level reviews degree.
To set up taps, fit the bottom of the furthest adaptable faucet connector to the proper supply pipe by making a compression join; then do the same for the other faucet.
Switch on the water supply as well as examine all joints and brand-new pipework for leakages and tighten them if needed. Load the bathtub and additionally check the overflow outlet and the typical electrical outlet for leakages.
Ultimately, fix the bath paneling as described in the producer's instruction manual. Tiling as well as sealing around the tub must wait up until the tub has been used a minimum of once as this will settle it right into its final placement.
Fitting New Taps
If the tails of the brand-new taps are plastic, then you will certainly require a plastic adapter to prevent damage to the thread. One end of the adapter fits on the plastic tail of the tap and the various other end offers a link to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly call for reducing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next off, place the faucet in the mounting opening in the bath/basin guaranteeing that the washing machines are in location in between the tap as well as the sink. Safeguard the tap in place with the supplier offered backnut. When the faucet is securely in place, the supply pipes can be attached to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with regular tap ports. The previous kind must be attached to the faucet finishes initially, tightening up just by hand. The supply pipelines can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the location where the bathroom satisfies the ceramic tile, it is required to seal the joins with a silicone rubber caulking. This is essential as the fitting can relocate enough to split a rigid seal, triggering the water to penetrate the wall between the bath as well as the tiling, causing difficulties with dampness and possible leakages to the ceiling below.
You can choose from a variety of coloured sealers to assimilate your fixtures and fittings. They are marketed in tubes and cartridges, as well as can sealing spaces approximately a width of 3mm (1/8 inch). If you have a larger void to fill, you can fill it with twists of drenched paper or soft rope. Remember to always fill up the bath tub with water prior to securing, to allow for the movement experienced when the tub is in use. The sealant can break relatively very early if you do not take into account this movement before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are additionally conveniently readily available on the marketplace. It is a good idea to fit the ceramic tiles utilizing water-resistant or waterproof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you enjoy reading up on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Place feedback further down. We will be pleased to hear your thoughts about this blog post. In hopes that you come back again before long. Are you aware of somebody who is fascinated about the subject? Do not hesitate to share it. Thank you so much for taking the time to read it.
Prices & Booking Report this page